Pattern of a blouse with a ray dart (Product code: 9062)

The set of patterns for this model includes:

Back pattern

Pattern of a shelf

Collar pattern

Pattern of the stand

Sleeve pattern

Cuff pattern

Sleeve placket pattern

You also need: adhesive interlining, 9 buttons.

Cut:

Main fabric:

1. Make sure your printer is connected to your computer and working properly.

2. Open the PDF file with the patterns that you purchased from our site.

3. In the print settings window, select A4 paper size, which corresponds to the standard paper size in most countries of the world.

4. Select "Book" orientation. This will ensure that the patterns are positioned correctly on the page.

5. Set the "Real size" option. This will ensure the exact size of the patterns and their display on the paper according to the dimensions specified in the file.

6. Select the "One-Sided Print" option. Make sure all the print options meet your needs, then click the Print button to start printing.

If you have any difficulties with printing patterns, please contact our customer service at This email address is being protected from spambots. You need JavaScript enabled to view it..

Seam allowances: Hem allowance for the bottom of the product – 1.5 cm, along the cut of the bar – 0 cm, other seams – 1 cm.

When sewing parts, pay attention to the notches - they must match!

1. Use adhesive interlining to duplicate the one-piece placket, cuffs, top collar and inner stand.

2. Fold the top collar with the bottom face inward. Sew down the ends and flap of the collar. Trim the seams. Turn the collar out, straighten and iron. Place the stand pieces face to face, place the finished collar between them, align the notches and stitch, while turning the ends of the stand. Start and end the stitch strictly at the marked seam line for setting in the stand. Turn out the finished collar and iron it.

3. Sew darts on the shelves. Iron the waist darts to the middle of the front, and the chest darts from the middle. Sew the darts on the back. Iron the darts to the middle seam. Sew the center back seam. Overcast and iron the seam.

4. Sew shoulder and side seams. Overcast the seams and press to the back. Fold the planks to the wrong side twice and place a finishing stitch along the inner edge of the plank.

5. Sew the top stand with collar into the neckline, tuck the open edge of the bottom stand and stitch it into the stitching seam of the top stand. Place a finishing stitch along the stand and collar.

6. Processing the vents: Cut the sleeve along the intended line, cutting the corner at the top of the cut. The area from the cut to the intended line, equal to 1.7 cm, is folded inward twice by 0.5 cm and stitched. Fold the bar lengthwise in half with the right side facing inward and stitch the corner to the cross mark. Cut seam allowances close to the stitching, cut the seam allowance at the end of the stitching. Turn the strip inside out, iron it and stitch along the fold line from the bottom to the transverse mark by 0.1 cm. Fold the placket with the sleeve facing inward and stitch the inside along the marked line. Cut the sleeve at the end of the stitching crosswise from the cut to the stitching line. Bend the bar to the front side, fold the open edge and stitch. Align the bar with the marked line on the sleeve and stitch the upper corner along the contour and along the transverse mark.

7. Stitch and overcast sleeve sections. Sew in the sleeves, placing them at the edges.

8. Fold the cuffs in half and stitch the short sides and the area to the notch. Cut the allowance near the notch. Turn the cuffs inside out and iron them. Place folds on the sleeve along the marked lines. Sew the outside of the cuff to the sleeve. Fold the inside of the cuff over and stitch into the sewing seam. Sew the loops on the cuffs and sew on the buttons.

9. Overcast the bottom of the product, iron it on the wrong side and topstitch.

10. Sew the loops on the right shelf, and sew buttons on the left.